Skip to main content

Gear investigation : Banbao LEGO airplane




Running on ground


Motion not too smooth



Completion date: April 30, 2020

Observations
1. Motor to propeller is 24=40=40:24:16.   So propeller is running 1.5 times faster than the motor (24/16=1.5)
2. Motor to wheels is 24=40=40:24. Same speed.
3. The belt can be used to pass on the same speed from one gear to another, and these gears would move in the same direction. The belt can also be used to pass the motion over a longer distance.
4. The axle can be used to pass on the same speed and same direction of the gear on the same axle. Also, the axle can be used to displace the motion to another gear on the same axle.
5. One gear can invoke motions on multiple gears.
6. Gear’s direction can change from left/right motion to become front/back motion by using a direction-changing gear.  While this is happening, the difference in gear sizes can speed up (or slow down) the next set of gear motions.

Comments

Post a Comment

Popular posts from this blog

DIY Keyboard drawer installation

Completion Date: May 24, 2020 Work from home has given me chance to use my DIY table (35cm*50cm) ever more than before.  I feel great, but I realize the fact that I don’t have enough space if I want to work on my iPad at the same time.  I bought this mini drawer tracks so I can create this space. Material:  - 10 inch (25cm) keyboard drawer tracks, 1 pair (Taobao, RMB12.5) - 24*36cm wooden board (left over I have at home) Steps: 1.  Stretch the keyboard tracks to full extent.  Fit the wooden board to the end of the track and mark the holes with pencil. 2. This is 2.5mm drill bit.  Drill pilot holes to the marked holes.  Do the same for the other side. 3. Take my table top out and flip upside down.  Fit the keyboard drawer and trace the outline and mark the holes with pencil.  Re-verify the keyboard outer edge aligns in parallel with the table top’s outer edge. 4. Drill the holes ...
Post a Comment
Read more

Gear investigation: Banbao Lego crane

Completion date: May 16, 2020 1. Gear ratio: 8:24:40. The bottom wheel cranking the string at speed (8/24)*(24/40)=0.2x speed of the motor. 2. The top two wheels looks like pulley system to me, but I am not sure about the spinning speed of the top wheels, the first top wheel is slower than the bottom wheeler, that I observed. 3. The beginning of the bottom wheeling action is pulling less string because the circumference is small (less string winded).  So it pulls the string faster gradually as more string is added to the circumference. 4. Note I added the rewind crank on the other side of the motor. This is the final instruction of the Banbao booklet. All the builds have been fun for me, I got to know more about gears now (though still primitive). My thoughts towards the gear mechanism is that it is not as efficient as I thought it would be. - requires many gears to do 1 simple thing - gear design has to match the many requirements of the space, dist...
Post a Comment
Read more

Star cushion

Completion date: Jun 12 2020 Steps 1. Trace the star shape onto the fabric.  Double over the fabric.  Apply pins to secure the edges.  Cut out. 2. Install a platform on the sewing machine.  3. Whenever I need to turn the fabric I place the needle down on the fabric before turning the fabric.  Sew until I get a 15 cm opening. 4. Flip the fabric inside out and put the foam filling inside the star cushion.  Bind off the opening by hand sewing. My daughter requested for a star cushion.  I recycled filling of a foam-type cushion into this one.  This was the first time I used a platform.  The table was not long enough but I put something underneath to support the platform.  She was pleased with it though it wasn’t pink as she originally requested.  Below in the picture was her little hand!
Post a Comment
Read more