Skip to main content

Keyboard silicon cover



Completion date: May 5, 2020

Dust gets into the keyboard and I usually buy these silicon keyboard covers. There isn’t a mould for this Rapoo keyboard, so I bought a generic one on Taobao.  Because I stand the keyboard up when I don’t use it, so the silicon cover occasionally falls down. I need a way to secure the cover from falling off.

Materials
- Silicon keyboard cover 14cm x 45cm (RMB$9.58/each, on a buy one get one free, so it’s around RMB$5/each)

Steps
1. Cut the silicon short so it can cover all the keys. Cut the corners round.

2. With the leftover silicon, cut 2 strips 1cm x 14cm.


3. Mark at 0.5 margin.  Punch 2mm holes at the marks.




4. Cut a straight line in the middle from top hole to bottom hole.



5. Now it looks like an elastic band. Fit the keyboard through the bands at the ends to secure the silicon cover.



Comments

Post a Comment

Popular posts from this blog

DIY Keyboard drawer installation

Completion Date: May 24, 2020 Work from home has given me chance to use my DIY table (35cm*50cm) ever more than before.  I feel great, but I realize the fact that I don’t have enough space if I want to work on my iPad at the same time.  I bought this mini drawer tracks so I can create this space. Material:  - 10 inch (25cm) keyboard drawer tracks, 1 pair (Taobao, RMB12.5) - 24*36cm wooden board (left over I have at home) Steps: 1.  Stretch the keyboard tracks to full extent.  Fit the wooden board to the end of the track and mark the holes with pencil. 2. This is 2.5mm drill bit.  Drill pilot holes to the marked holes.  Do the same for the other side. 3. Take my table top out and flip upside down.  Fit the keyboard drawer and trace the outline and mark the holes with pencil.  Re-verify the keyboard outer edge aligns in parallel with the table top’s outer edge. 4. Drill the holes ...
Post a Comment
Read more

Gear investigation: Banbao Lego crane

Completion date: May 16, 2020 1. Gear ratio: 8:24:40. The bottom wheel cranking the string at speed (8/24)*(24/40)=0.2x speed of the motor. 2. The top two wheels looks like pulley system to me, but I am not sure about the spinning speed of the top wheels, the first top wheel is slower than the bottom wheeler, that I observed. 3. The beginning of the bottom wheeling action is pulling less string because the circumference is small (less string winded).  So it pulls the string faster gradually as more string is added to the circumference. 4. Note I added the rewind crank on the other side of the motor. This is the final instruction of the Banbao booklet. All the builds have been fun for me, I got to know more about gears now (though still primitive). My thoughts towards the gear mechanism is that it is not as efficient as I thought it would be. - requires many gears to do 1 simple thing - gear design has to match the many requirements of the space, dist...
Post a Comment
Read more

Star cushion

Completion date: Jun 12 2020 Steps 1. Trace the star shape onto the fabric.  Double over the fabric.  Apply pins to secure the edges.  Cut out. 2. Install a platform on the sewing machine.  3. Whenever I need to turn the fabric I place the needle down on the fabric before turning the fabric.  Sew until I get a 15 cm opening. 4. Flip the fabric inside out and put the foam filling inside the star cushion.  Bind off the opening by hand sewing. My daughter requested for a star cushion.  I recycled filling of a foam-type cushion into this one.  This was the first time I used a platform.  The table was not long enough but I put something underneath to support the platform.  She was pleased with it though it wasn’t pink as she originally requested.  Below in the picture was her little hand!
Post a Comment
Read more